GEPRC 130X "Rage Potato"

By BirdbrainRC on Aug 02, 2017

16  1,456  7

So I decided that I was going to build myself a little 3" quad as an always available freestyle rig for travelling. It just so happened that the Runcam Split was announced whilst I was pondering, so I ended up speccing a build around it. Also started to get into racing around the same time, so the build switched focus a little towards going fast too.

Parts

Obviously the Runcam Split was an integral part of the build, finalised straight away. I also decided soon on that I wanted use a TBS Unify HV Race for ease of use and its acceptance in race events. Knowing I'd board mount the Unify, and that the Split's board would be to deal with, I had to pick an FC with a built in PDB. Recent positive experience meant that Betaflight OSD was also a must, so I went for a Kakute F4. Being as it wasn't going to be a featherweight build, I went for Tornado 1407s. 20A ESCs from Unmanned Tech and an RSFSB OrangeRx receiver rounded out the electronics.

The frame was a different matter. Initially I bought an Atto DC130, which is a lovely frame but the short rear arms meant it would be near impossible to fit the ESCs on the arms. With a full size FC, the props overlap with the boards too, making for a tricky build with 3 boards in the stack. As a result, I picked up a GEPRC GEP130X instead - it has loads more room. I also swapped the short standoffs for standard 35mm ones to get enough vertical clearance.

Build

The build went remarkably smoothly considering the small size of the frame and despite the fact it was my first non-5" build. I started with a dry fit of the components in the stack to check clearance, and found that there was very little wiggle room on the Split's camera module - the angle would only be tweakable from around 35 to 50 degrees. I also discovered that the front standoffs show in the HD footage (being slightly wider field of view than the FPV feed), so I swapped the chunky green standoffs for skinnier black ones at the front to try and minimise the amount of the picture lost.

After this I started soldering it all together. The Kakute was mostly nice to work on - one slightly awkward part was the frontmost solder pads for the camera power and video in, which are under the ribbon cable to the IMU. I found the best way to get it out of the way was to push it backwards and tack it down with electrical tape until the soldering was done.

I soldered the Unify cable straight to VCC on the Kakute, having had no noise issues in the past running it straight off the battery. I also soldered a 5V pigtail to the board to power a race transponder if required. An XT60 on a pigtail was added for battery connection - whilst a lot of smaller 4s batteries use XT30 connectors, I was planning for 1000mAh packs and the affordable ones I found used XT60s.

In order to fit the ESCs on the arms I had to leave the motor wires a little long and coil it on top of the ESC. To help with the soldering the motors to the ESCs I taped the ESCs to my work mat in place of using a third hand. Once in place and soldered to the Kakute I covered the ESCs with electrical tape which also hides the extra wire. The receiver was cable tied to the inside of the top plate, and a cable routed through the stack to it from the flight controller.

Antennas were routed out on heatshrunk cable ties, and the Unify pigtail was cable tied to the rear standoffs, allowing for easy access to the flight stack after unplugging the receiver. There is enough free space behind the stack for an i-Laps race transponder.

Final build weight without battery comes in at 196g, and 320g with a 1000mAh pack - quite weighty for a 3"! Considering the HD recording and grunty motors though, it's more bearable. Initial flying impressions are good - it flies like a 5" quad, but every little gap looks so much more makeable. All in all, I'm really happy with how the build went and am looking forward to putting it through its paces on the track!

Flight video

Photos

Part List

Frame

Geprc GEP130X 130mm 2.5mm Arm Carbon Fiber Frame Kit w/ 5V 12V PDB Board XT60 Cable for RC FPV Racing Drone (5 builds)
Banggood.com
$34.99

Flight Controller

Holybro Kakute F4 AIO All in One V2 Flight Controller STM32 F405 MCU Integrated PDB OSD for RC Drone (42 builds)
Banggood.com
$43.91

ESCs

4 x Chaos BLHeli_S Dshot ESC (11 builds)
Unmannedtechshop.co.uk
See Site

Motors

4 x Brotherhobby Tornado T1 1407 3600KV 4S Racing Edition Brushless Motor for FPV Racer (193 builds)
Banggood.com
$67.96

Propellers

RaceKraft 3041 Q4CS Quad-Blade Propeller Pack
Unmannedtechshop.co.uk
See Site

FPV Camera

Runcam Split WDR WiFi FPV Camera 1080P 60fps HD Recorder Short Lens/RC25G GoPro Lens Orange/Black (61 builds)
Banggood.com
$66.99

FPV Transmitter

TBS Unify HV / FrSky RX Mounting Board (2 builds)
Hobbyrc.co.uk
See Site

FPV Transmitter

TBS Unify Pro Race VTX HV 5.8GHz (SMA) (556 builds)
Hobbyrc.co.uk
See Site

Antenna

5.8G FPV unbreakable TX/RX Racing Antenna (SMA) (3 builds)
Hobbyking.com
$5.18

Receiver

OrangeRx Futaba RSFSB S-FHSS/FHSS Compatible 8ch 2.4Ghz SBus Receiver
Hobbyking.com
$20.00

Batteries

Turnigy Bolt V2 1000mAh 4S 65~130C High Voltage Lipo Pack (3 builds)
Hobbyking.com
$19.66

Radio

Jumper T-Lite 16CH Hall Sensor Gimbals CC2500/JP4IN1 Multi-protocol RF System OpenTX Mode2 Transmitter Support Jumper 915 R900/C (21 builds)
Banggood.com
$69.99

Radio

FrSky Taranis Q X7S Radio w/ Upgraded M7 Hall Sensor Gimbals (Carbon Fiber) (25 builds)
Getfpv.com
$187.99

Radio

FrSky TARANIS X-Lite (Black) (64 builds)
Hobbyrc.co.uk
See Site

Goggles

ORQA FPV.One OLED FPV Goggles (12 builds)
Getfpv.com
$549.00

Goggles

FatShark Dominator HD 2 Hydro-Dipped Urban Cam Grey and White FPV Goggle
Hobbyking.com
See Site

HD Camera

Hawkeye Firefly 6S 4K WiFi Sport HD DV Camera - $75.31 |GearBest.com
Gearbest.com
$75.31

HD Camera

HawKeye Firefly Q6 4K 120 Degree Angle Action Camera - $59.14 |GearBest.com (2 builds)
Gearbest.com
$59.14

HD Camera

GoPro HERO6 Black - Waterproof Digital Action Camera for Travel with Touch Screen 4K HD Video 12MP Photos (5 builds)
Amazon.co.uk
See Site

HD Camera

GoPro HERO5 Session (300 builds)
Getfpv.com
$199.99

HD Camera

RunCam 5 Orange 12MP 4:3 145°FOV 56g Ultra-light 4K HD FPV Camera for RC Drone (18 builds)
Banggood.com
$102.49

HD Camera

GoPro Protective Lens (GoPro Official Accessory)
Amazon.co.uk
See Site

Misc Parts

4pcs 35mm M3 Aluminium Stepped Standoff - Green
Hobbyrc.co.uk
See Site

Misc Parts

I-Lap FPV Drone Transponder
T9hobbysport.com
See Site

Video Receiver

Furious True-D V3.5 Diversity Receiver System Firmware 3.8A (FatShark Attitude Version)SKU: FPV-RX-TRUD3.8A (27 builds)
Furiousfpv.com
$68.00

Video Receiver

ImmersionRC RapidFIRE w/ Analog PLUS Goggle FPV Receiver Diversity Module (179 builds)
Banggood.com
$149.00

Radio Module

TBS CROSSFIRE NANO TX (9 builds)
Pyrodrone.com
$69.95

Radio Module

Frsky R9M Lite - Radio Transmitter Module (Black) (11 builds)
Getfpv.com
$47.99

Radio Module

FrSky R9M 2019 915MHz RC Transmitter Module w/ Super 8 Antenna (ACCST/ACCESS)Default Title (17 builds)
Racedayquads.com
$45.99

Backpack

MultiStar Premium Multirotor Travel Backpack
Hobbyking.com
$47.03

Backpack

TORVOL QUAD PITSTOP BACKPACK PRO (5 builds)
Risingsunfpv.com.au
$359.99

Accessories

TrueRC True-MOX 868MHz Antenna
Hobbyrc.co.uk
See Site
Show stores (12)

Discussion

Sign in to comment

delta_fpv   Aug 02, 2017  

please keep me updated on how it performs, looks fucking awesome, have been thinking of building a 3inch but chose a 5inch in the end.

Oeliboeb   Aug 06, 2017 

5 inch quads are more versitile in the end imo. I like the idea of 3 inch quads but its so much more expensive than 2inch brushless quads... They look so cute tho

delta_fpv   Aug 06, 2017 

WELL, EXACTLY.

TheLeprechaunPirate   Aug 04, 2017  

Thanks for posting this. I have this frame, and was thinking of using spare parts to make a similar build with a Split. But instead I threw it all on my Shrieker. I do want to do a weight comparison, but I don't have a scale at hand. I did notice the slight heaviness of the quad.

Whiffles   Aug 02, 2017  

I'd love to see some video. I built a similar quad on the Volcor frame and I love it! The GEP130X was the first frame I ever used, so it really takes me back to see it still getting use. How are those props? Do your motors get hot? I've been flying the RK 3030 quad-blades and they're still great after all this time.

BirdbrainRC   Aug 03, 2017 

I actually saw your build when I was deciding on the GEP130X! Very clean, I think I'll end up doing something similar with the Atto DC130 frame I now have going spare :) I've added a video link, apologies for the hideous youtube compression. Also have been struggling to work out how to embed images and videos properly in descriptions here, any tips?

Still tuning my GEP130X out at the moment, have actually swapped over to DYS 3045 triblades rather than the Racekrafts as I was getting a bit of vibration and wondering if they were the reason. Video is still a bit jello-y; have you had any issues with your Volcor?

Whiffles   Aug 03, 2017 

I found that soft mounting the camera with double sided tape inside the adapter works pretty well to eliminate jello. I had to do that at first due to the screws popping out of the adapter, but since I added the screws the jello got worse so I'm going back to the double sided tape.

Guides & Reviews

Jun 21, 2021

AirbladeUAV has done it again and this time they've brought long range to the 5" class! Based on the popular Transformer Mini, the new Transformer 5" Ultralight adopts a lot of the same design philosophies with larger props and more payload capacity. It can fly upwards of 20 minutes on a 4 cell Li-Ion battery pack and in ideal conditions it's got a range of over 4 to 5 miles. In this guide I'll walk..

Read more
Mar 04, 2021

With the release of the DJI FPV Drone cinematic FPV has become a lot more accessible, but you certainly don't want to crash a $750 drone! The QAV-CINE Freybott is a compact, lightweight cinematic FPV drone that can take a hit and keep going. It's a lot safer to fly indoors and around people. With a naked GoPro or the SMO 4k you can capture some great stabilized footage. In this guide I'll show you..

Read more