GEPRC Crocodile 7" HD - Semi Slammed

By wrong17 on May 23, 2022

25  1,057  13

I purchased the GEPRC Crocodile 7 frame without any of the original hardware, but I was told that it normally used 25mm standoffs. I wanted to slam this quad with 15mm standoffs, but it made it very difficult to remix any of the 3D models I plan to use. Plus, it will be very tight squeeze for the Caddx Vista because it is 13mm tall. I end up going with 20mm standoff instead, so that should give me a lot a wiggle room. I assume this frame is not very popular because I am having trouble finding 3D printed parts for it. I am not sure how I want to place the ESC and FC stack yet because the frame has so much space I can either stack them on top of each other or one in front of another.

Since the Caddx Vista will sit all the way in the front of the frame, I will extend and convert the antenna from a ufl to a RP-SMA connector. I also like having the RP-SMA connector because it allows me to remove the antenna for easy of transport. Initially I purchased a 15cm extension but it is 2mm too short, so I had to by 20cm instead.

3D Prints

Alt Tag I have spent most of my time figuring out the 3D printed parts I plan to use for this build. I tried looking at various locations for Free STL files to print stuff for the Croc 7, but I am not liking the items found. When I remix 3d models it requires a bit of trial and error. Sometimes I would reprint the same parts repeatedly because I need to make changes to it. I have a few 3D designs that I tend repurpose on multiple builds because it works well. For example, the Slammed Squirt that Drone CO Production created, I have remixed it so it will fit on a Source One v4 7” quad. The reason why I like it so much is because the GoPro camera is more forward more so you can have a lower camera angle and not catch the props in the camera’s view. I was planning to do the same with this build too, but I wanted to try something else. Another favorite design, it the DJI HD conversion kit I purchased from BOPILOOT.

Alt Tag The first attempt on remixing the Floss parts to the Crocodile frame turned out well but I did not push the FPV camera forward enough. So, the HD camera might get a tiny glimpse of the props on extreme maneuvering if you have the GoPro set to SuperView. I also noticed another problem with this FPV camera mount. It did not give me enough clearance to Caddx Polar pro camera unless I use the very bottom screw hole because the top of the camera will contact the top plate. All these issues are because the camera mount needs to be pushed forward more.

Alt Tag This is the second version where I move the camera 7mm forward and it fixed all my problems. But the GoPro mount holes are different so now I need to adjust the mounts too. In the first version I incorporated 2 holes for the GoPro mount, so it has an adjustable camera angle. To maintain the lowest profile, it is best to have on angle for each camera mount and that is what I did for the second version.

Alt Tag Here is a WTF the moment for me. The shape of the arms is different between the front and rear. I am talking about the ends where you mount the motors. I used an image of the rear arm to create a vector image to extrude the shape in Fusion 360. I assumed the arm guards that I modeled would fit the front arms, but it did not. After overlaying the 2 arms shapes over each other, I think if I modeled the arm guards based off the front arms, it might work with the rear arms too. But with my luck, I happen to start with the rear arms first so that is why it would not fit the front arms.


Part List


GEP-LC7HD Frame - GEPRC (2 builds)

Flight Controller

Diatone Mamba F722 APP Flight Controller 30*30 (3 builds)


T-Motor F55A Pro II 55A 3-6s BLHeli32 4-in-1 ESC (16 builds)


4 x EMAX ECO II 2807 Brushless Motor - 1500KV

FPV Transmitter

Caddx Nebula Pro Micro Vista Kit - Choose Color (15 builds)


TBS Crossfire Immortal T Antenna V2 - Extra Extended (9 builds)


iFlight FPV Drone Antennas (LHCP RP-SMA Male 150mm Antenna) 2PCS for Long Range HD FPV Drone Like as Titan DC7 Chimera4 Chimera7


TBS Crossfire Nano Rx FPV Long Range Drone Receiver (1491 builds)

3D Printed

Floss 3.0 & 3.0L SMA Mount by Brain-3D
See Site

3D Printed

GEPRC Crocodile 7 Extended GPS by keith124
See Site

3D Printed

Hyperlite Floss v2 - DJI FPV conversion
See Site

3D Printed

SMA connector standoff mount by chaserporter
See Site

3D Printed

Swissknife : XT60 holder for top or bottom mounted battery by nracing
See Site

3D Printed

GEPRC Crocodile7 HD Plus Collection of Parts - SMA Antenna - Matek GPS - GoPro - FPV Camera - Immortal T Mount by wrong17
See Site


[60PCS] M3 Finishing Countersunk Washers, Anodized Aluminum Alloy, Head Washers Gaskets Cup Shim for Screw RC/FPV/PC/Drone/Mecha

Misc Parts

CORONIR 8PCS 20CM IPX/UFL to RP-SMA Female Extension Cord Antenna WiFi Pigtail Cable IPEX U.FL IPX Connector to RP-SMA Female Ja (2 builds)
Show stores (7)


Sign in to comment

bentoogood   Apr 22, 2023  

How do you find it flies with the 2807s, and flies overall? Do you think it's better suited to 2507s? The build looks excellent!

wrong17   Apr 22, 2023 

Your are right, a lighter weight motor would better for this frame and the 2807 is an overkill. So, the 2507 might be the best size motor for this frame. I no longer have this frame anymore so I would not know for sure. If you do this swap, please let me know how it turns out!

markpurnell   Feb 03, 2023  

Thanks for the inspiration for my first 7" build! I would post a pic of it, but the Upload Photos function doesn't appear to work!

wrong17   Feb 03, 2023 

Good luck with your built. Too bad the upload function does not work for you. Try to send me a message with pictures of it, I would like to see what you have done.

Lennyp   Aug 04, 2022  

you should donate all those extra 3d prints to my " poor mans croc" lol

wrong17   Aug 04, 2022 

I would be happy to, but I might have thrown them away, I have to check. Sent me a PM if you really want them.

jacobhue   Jul 25, 2022  

GEPRC Crocodile 7" HD is a semi-slammed action cam that has a wide range of functions. It is waterproof, shockproof, and dustproof. It also has a built-in Wi-Fi and GPS so that the user can have an easy time uploading videos to social media platforms.

This action cam comes in two colors - black and white. The black color version comes with a battery pack while the white color version comes with a battery pack and an external power bank.

butcher51   Jul 24, 2022  

Gorgeous! Also really clean 3d prints :)

wrong17   Jul 25, 2022 


Philm0   May 28, 2022  

Love the clean slammed look, and your tri-color prints. Good job mate.

wrong17   May 28, 2022 


Madcatmike3d   May 24, 2022  

Absolutely beautiful.

wrong17   May 24, 2022 


Guides & Reviews

Jun 21, 2021

AirbladeUAV has done it again and this time they've brought long range to the 5" class! Based on the popular Transformer Mini, the new Transformer 5" Ultralight adopts a lot of the same design philosophies with larger props and more payload capacity. It can fly upwards of 20 minutes on a 4 cell Li-Ion battery pack and in ideal conditions it's got a range of over 4 to 5 miles. In this guide I'll walk..

Read more
Mar 04, 2021

With the release of the DJI FPV Drone cinematic FPV has become a lot more accessible, but you certainly don't want to crash a $750 drone! The QAV-CINE Freybott is a compact, lightweight cinematic FPV drone that can take a hit and keep going. It's a lot safer to fly indoors and around people. With a naked GoPro or the SMO 4k you can capture some great stabilized footage. In this guide I'll show you..

Read more