Tadpole is the Bestpole

By Ewiley on Apr 28, 2021

11  262  6

For some reason the 2.5" (or 65mm) size is just my favorite all-around size, despite there being very few options for frames and props. I'm mostly inspired by the excellent Tinyhawk 2 Freestyle, but the EMax vendor-lock-in makes it very hard to do more with that platform.

Enter the Tadpole 2.5: A lightweight frame from the wonderful folks at Armattan; tiny but still built to their high standards. It's not got a lot of space in the frame, but it's very well-designed. The default is to use a 16x16 stack, but I really, really hate that form-factor (everything is pin headers and pain). Fortunately they designed a 25mm whoop bracket which opens up a plethora of possibilities, what with all the new AIO boards out there. You could probably use a whoop board without the bracket if you don't stack anything on top since there's just two holes in the frame bottom for it. Cabling and soldering will likely be a bit of a challenge and it took me 2-3 tries to get everything worked-out exactly right.

The back-end is cramped a bit with a R9 receiver, capacitor, Foxeer lollipop vtx antenna, and mini 900mhz T-antenna. I routed the battery leads around the outside of the rear bracket and it just clears the rotors. It's not great but it all seems to work.

Lets talk motors. The 9x9 mount pattern is the 11xx standard, and most Xing c-clips fit just fine in it. Originally I built this with 1204s, but the battery life was garbage. The Xing 1105 4500kv motors fit the bill perfectly (and the colors are extremely fly). They have great battery life on 4s and pack more than enough punch to fly the whole rig and an insta 360 go. I love these motors! My only complaint is they only have 2 M2 holes for mounting props (I always use screws to t-mount the 1.5mm shaft props). I've had a set of motors that finally wore-out the holes so it'd be nice if there were 4, but it's a minor quibble.

For the main board I opted for a hakrc AIO because 20A for like $35 you can't go wrong. Who cares if it's just an F4? The only awkward part is soldering the negative battery lead is super close to the USB port. BUT since the outside of the USB is ground, it actually doesn't matter if you get a bit messy with the solder.

Video-wise I got a relatively OK flywoo VTX (with screw-locking u.fl connector) and a Runcam Racer 2 nano (eh, it's not great but it works). There's not a ton of clearance between the back of the camera and the front whoop mount, so be careful.

Overall I've got it at 156g with a 4s 450mah battery. This is a great power/weight ratio and a very suitable park flyer for dinking around playgrounds and other very non-serious locations. What's surprising is just how much lighter than the next size (an Armattan Gecko 3") which tops the scales at 300g.

Photos

Discussion

Sign in to comment

daich   14 days ago  

nice build. i agree, there is something magical about 2.5"
they throw around better than a 3"

Polymerization   29 days ago  
1

man, those are some really good looking motors and though metal parts on frames is not the lightest, I think they look so cool

Ewiley   29 days ago 
1

Yeah true not as light as carbon or plastic bits but well worth it to not smash my camera or fall apart after a couple of knocks at the park :)

feeksfpv   May 12, 2021  
2

love these motors, also have a blast flying 3-2.5" quads, using these on a x-knight frame with 3" props

Jodie Froster   Apr 29, 2021  
1

Is that electrical tape on your cap hangin out the back?

Ewiley   Apr 29, 2021 

It is! good eye :) I like to run the wires directly from the main PCB rather than off of the lead so I was worried that the leads might short against something while getting it all sorted out, so it was really just a temporary bodge. I'll eventually replace it with some heat shrink or hotglue.

Guides & Reviews

39 5,074  30
Mar 04, 2021

With the release of the DJI FPV Drone cinematic FPV has become a lot more accessible, but you certainly don't want to crash a $750 drone! The QAV-CINE Freybott is a compact, lightweight cinematic FPV drone that can take a hit and keep going. It's a lot safer to fly indoors and around people. With a naked GoPro or the SMO 4k you can capture some great stabilized footage. In this guide I'll show you..

Read more
44 9,460  53
Nov 19, 2020

FPV has had quite a journey. Just a few years ago we started racing drones around a track and doing flips over trees, but professional cinematic FPV is a more recent development. DJI has always owned the drone photography market, but smaller acrobatic drones are starting to enter the market. They have the advantage of close proximity flight indoors and around people. There's more artistic freedom and..

Read more