HX-100 SE

By valek on Apr 30, 2020

9 516 4

HX-100 Build
-betafpv frame, motors and FC but used different RX, 3D print parts and AIO Camera VTX
-2x PH 2.0 connectors wired in parallel for use with 2x 220mah whoop batteries at once (this is still a 1s only build)
-both the 2x 220mah at 4.35v batteries or 1x 550mah at 4.2v gives a 4-5min flight time.
-used a Full Flysky RX because of all the negative range reviews of the built in RX versions of the board

This is a very light quad and quieter than most whoops. just don't lose it in the tall grass.

Photos

Part List

Frame	HX100 SE T300 Carbon Fiber Frame (8 builds) Betafpv.com	$8.99
Flight Controller	F4 1S Brushless Flight Controller V2.2 (18 builds) Betafpv.com	$34.99
Motors	1102 Brushless Motors (6 builds) Betafpv.com	$39.99
Propellers	Gemfan 65mm 2-Blade Propellers (1.5mm Shaft) (4 builds) Betafpv.com	$0.79
FPV Camera	Eachine TX02Pro TX02 PRO with Smartaudio AIO 5.8G 40CH 200mW VTX 700TVL 1/4 Cmos FPV Camera NTSC Banggood.com	$13.99
Receiver	Flysky　FS-A8S FS A8S 2.4G PPM付き　　8CHミニレシーバー　i-BUS SBUS出力 (10 builds) Banggood.com	See Site
Batteries	10Pcs URUAV 3.8V 550mAh 50/100C 1S HV 4.35V PH2.0 Lipo Battery for Emax Tinyhawk Kingkong/LDARC TINY (2 builds) Banggood.com	$31.19
Batteries	4pcs 230mAh 1S Lipo Battery 30C 3.8V for Tiny Whoop Blade Inductrix JST-PH 2.0 Connector Amazon.ca	See Site
Radio	Team BlackSheep Tango 2 PRO Crossfire Radio Controller (14 builds) Airbladeuav.com	$199.99
Goggles	FatShark Scout FPV Goggles (10 builds) Racedayquads.com	$199.99

Show stores (5)

Like Copy Part List Follow valek

Discussion

DrewFPV May 05, 2020

How does it fly? I am thinking about building one of these with a mobula 7 f4 fc and Gemfan 2-bladed props.

valek May 05, 2020

it fly's amazingly well. its like a 5" trainer quad. I think with the bi-blade props not grabbing the air as well as tri-props it drifts around corners like my 5" does. its a perfect mini copy.

your mobula 7 fc will be more than enough although i think the difference in the 0802 motors of the mobula will have a different result than the 1102 i used. also i think the press on prop bolt is slightly larger diameter at 1.5mm for the 1102's. here's a video of me flying but no comments on my lack of skills with the model or the video editor

DrewFPV May 06, 2020

OK Thanks for replying I was thinking about using fpvcycle 1202,5 11500kv motors

valek May 09, 2020

I'm sure your build should fly fantastic and have a little more umph than my build.

Guides & Reviews

91 19,645 27

Build a 5" Long Range Drone - Transformer Ultralight

Jun 21, 2021

AirbladeUAV has done it again and this time they've brought long range to the 5" class! Based on the popular Transformer Mini, the new Transformer 5" Ultralight adopts a lot of the same design philosophies with larger props and more payload capacity. It can fly upwards of 20 minutes on a 4 cell Li-Ion battery pack and in ideal conditions it's got a range of over 4 to 5 miles. In this guide I'll walk..

66 15,925 61

Build a DJI FPV Cinewhoop - QAV-CINE Freybott Edition

Mar 04, 2021

With the release of the DJI FPV Drone cinematic FPV has become a lot more accessible, but you certainly don't want to crash a $750 drone! The QAV-CINE Freybott is a compact, lightweight cinematic FPV drone that can take a hit and keep going. It's a lot safer to fly indoors and around people. With a naked GoPro or the SMO 4k you can capture some great stabilized footage. In this guide I'll show you..

Guides and Reviews