Reborn freestyle Chameleon 6S

By M490fpv on Nov 09, 2018

16  1,611  3

Bought a used 5" chameleon frame for dirt cheap.
I like Chameleon flight characteristics very much. I've had 4 Chameleons already, so this is my fifth build (and first 6S Chameleon).

Because the weathers in Finland are really bad this time a year, i have much time to spend in my "quad factory". So I decided to put some extra hours in this quad to have some unique looks.

I decided to test a spray paint hydro dip finish to the frame. This is something I have not done before, but I've seen some really nice paint dips.
The spray paint hydro dip was a p.i.t.a. process, but i am really satisfied with the result. I used 4 different colors in the hydro dip, black, gray, white and neon yellow. After the hydro dip. i clear coated the parts with two layers of acryl clear coat.
My advise for the spray paint dip:

  • The water in the dipping tank should be as cold as possible. In warm water, the paint dries in seconds
  • Even if you have a really cold water, you should work fast: Shake all cans well before spraying and be quick in spraying the water surface. You have only about 30-45 seconds to dip the frame in the water from the first spray to surface.

Next I painted the camera pod side plates, capacitor and the Runcam micro eage frame with yellow color.

I didn't like the orange finish in Chameleon's aluminium parts, so I polished all aluminium parts the old fashion way by:  

  1. Removing the hard coating from the surfaces with P80-120 sand paper
  2. smoothing the surface, first P600, then wet sanding with P1200, P1500 and finally 2000.
  3. last a polish with aluminium polishing wax and fabric
    This polishing process is really slow, but gives a chrome like finish. This precise time it took about 8 hours to complete.

I used some printed parts in this builld.
Arm protector plates: https://www.thingiverse.com/thing:2651181
Lumenier AXII mount with integrated rx antenna mount: https://www.thingiverse.com/thing:2654814

In the electronics side there are nothing special, basically all components are proven reliable with 6S so I used them.
The Brotherhobby R6 2306 1800kv motors are really interesting and I cannot wait to get some stick time with 6S.

Some heat shrink here and there....

Now i think the Chameleon looks quite unique. I have not seen a polished Chameleon parts before (excluding Chameleon Ti of course!).

Photos

Discussion

Sign in to comment

UnderDawg   Dec 05, 2018  
1

.I like the process you used for the finish on this frame...I may give this a try sometime.

Moxl   Nov 20, 2018  
1

What a beauty! Nicely done :)

GZ   Nov 09, 2018  
1

Looks absolutly stunning with the hydrodipped frame, shiny, camera cage and those r6 motors!

Guides & Reviews

59 8,092  17
Jun 21, 2021

AirbladeUAV has done it again and this time they've brought long range to the 5" class! Based on the popular Transformer Mini, the new Transformer 5" Ultralight adopts a lot of the same design philosophies with larger props and more payload capacity. It can fly upwards of 20 minutes on a 4 cell Li-Ion battery pack and in ideal conditions it's got a range of over 4 to 5 miles. In this guide I'll walk..

Read more
55 9,934  58
Mar 04, 2021

With the release of the DJI FPV Drone cinematic FPV has become a lot more accessible, but you certainly don't want to crash a $750 drone! The QAV-CINE Freybott is a compact, lightweight cinematic FPV drone that can take a hit and keep going. It's a lot safer to fly indoors and around people. With a naked GoPro or the SMO 4k you can capture some great stabilized footage. In this guide I'll show you..

Read more