wrckit's atom mini: 2S 2" verdant deadcat

By deks on Jul 16, 2018

19  813  7

Dearest wrckit,

You wanted a micro. You had a frame, but no parts. I had lots of spares, and wanted to spread the micro love, and so it naturally came to pass. This is the story of your Atom mini.

Hello Atom my old friend

I also had the original Airblade/RotorX Atom Mini 83 - in fact it was my first brushless build - a hell of choice for a first build. I built mine up with 20x20 electronics as a 3S 2" screamer - it was probably >85g dry, ~130g AUW. 130g of angry bees. Sadly, that build met its end after one too many hard crashes onto concrete.

Since then, I've gravitated towards lightweight 2S builds using 16x16 electronics, and I've been having tons of fun. I was curious if I could build your Atom w/ 20x20 electronics and still have it be viable for 2S by making it lighter, now that I have a few micro builds under my belt.


I used the same stack that I had in my own Atom mini, the Omnibus nano f3 and Cicada 10A. I used 1103s instead of 1105s, and generally tried to build clean and tight. But even so, it was not to be... It was ~60g dry, kinda loud, and disappointing thrust-to-weight. On 2S, it needed ~40% throttle just to hover - not fun. I tried a few 3S packs and it was the powerful screamer that I remembered, but then it was getting heavy...

I came to a fork in the build: light, agile 2S neighborhood/proximity quad, or heavy, punchy 3S mini rocket?

I decided to go light. I replaced the 20x20 electronics with a 16x16 2S-only stack, mounted with VHB. That cut 7g, plus 4 steel M3 screws, down to ~50g. But it still left something to be desired: with 300mah 17g packs, it felt quiet and agile, but flight times were <2 minutes; with 450mah 32g packs, it got decent flight time, but got much louder and thrust-to-weight collapsed again.


I started looking for other weight to cut. There was still a lot of hardware: 6 steel M3 screws to hold the camera and top plate in place. Going to nylon would have saved a lot, but I really hate nylon hardware. I started thinking about if I could ditch the top plate and hardware altogether.

I started to design some canopies. Several very ugly iterations later, I went with a decidedly RotorX-inspired design. Very minimal, only 1.7g, still provides decent protection for the electronics. It's fairly thin TPU, so the camera is still going to see some impacts, but I also designed a light custom camera mount in TPU that has some give, so I'm hoping it'll be a bit more resilient. It attaches to the bottom plate with 3 M2 screws instead of 6 M3. That help cut another few grams.

Kill those Volts

Despite cutting another ~8% in weight, down to ~46.5g, it still didn't feel up to snuff.. The original problem still remained: power vs. flight time. My 32g Glacier 2S 450mah packs just felt too heavy on these 1103 8000kv Eaglepower motors. I decided to try the 10000kv Racerstars, hoping that they wouldn''t ruin battery life even more. They're also slightly lighter, and would save ~1.5g in total. Plus they come in purple.

Send it!

The 10k kv gives this guy the kick I was looking for. With a ~20g 300mah, it's reasonably quiet and pretty darn agile, though flight times are a little low, under 2.5 minutes or so doing light acro + cruising. With a ~30g 450mah, it's no longer that quiet, but it carries its weight well and flight times are closer to 3.5 minutes. A 350mah middle ground would be nice to explore, but I've been holding onto this guy for far too long.

Hope you have fun with it, wrckit!

Appendix: owner's manual


The R-XSR is on top of the stack. The bind button in on the back left, when looking down on the pod. You can just shove the canopy to the side to reach the bind button.

Battery lead

I've been using 2S balance connectors on all my light micros. It's not the best - they tend to get damaged in hard crashes and they stop mating securely, they're a slight pain to unplug, and I'm sure there's more resistance than XT30 or JST-RCY. But it saves 1g, is a bit more compact (especially than JST-RCY), and it means you can use any 2S battery without modification. I've thought about going to XT30 for everything, converting all my batteries over, but I've been too lazy :-). If you go with XT30 for everything, go for it though! Definitely better quality of life.


I included two each of:

  • Glacier 450mah: 31g
  • Airblade Premium (Bonka) 500mah: 32g
  • Airblade Basic (Tattu) 300mah: 20g

(I also tested the Turnigy nanotech 300mah (17g), but mine are old and not as nice as the Airblade 300). On the 300mah batteries, it feels nice and agile, but doesn't last long. You get nice flight times on the 450 and 500mah ones. I didn't test the Airblade batteries extensively, since I just got them (they probably have 2-3 cycles through them, nice and fresh feeling). The Glaciers are older, but still hold up reasonably well.


Get loose

I mostly flew it with a fairly loose tune. It works reasonably well for the DAL Cyclones 2035 as well as the RotorX/Gemfan 2035bn, and also reasonably well for batteries from 20-30g. There's definitely still some prop wash, but I thought lower would be more conservative. These should be on the FC as PID profile 1.

Roll: 27, 45, 22
Pitch: 40, 55, 40
Yaw: 70, 45
Antigravity gain: 5.5
Fliters: dynamic filtering on, PT1, both gyro notches off.


Before I sent it, I spent a few short packs pushing the PIDs to make it feel sharper and have less propwash. I didn't test this super extensively though, so please be mindful of motor temps! These should be on the FC as PID profile 2, and also the currently selected PIDs:

TODO: recover PIDs from DVR


I like the DAL cyclones because they stand up to abuse pretty well. The RotorX/Gemfan 2045BN are better for this build, I think - quieter and slightly lighter. But they bend a lot in crashes, making turtle mode unusable often. So I typically fly the Cyclones, and only use the RotorX/Gemfan when I want more quiet, and I don't take quite as many risks. (Oh BTW: the RotorX's bending is (part of) why I got stuck behind that fence. You remember the fence.)

On some motors, the RotorX/Gemfan are tight enough to not need prop screws. But the Racerstar motor shaft is a bit too short for that to feel secure, so it's probably safer to pay the 2g prop screw penalty.

I also included 1.9" RotorX/Gemfan hulkies. They're cute little guys, durable, don't bend that easily. They're going to generate less thrust, but I was thinking the added prop clearance might work well on this build. The Atom mini prop clearances are pretty tight, especially the distance between the back 2 props. I think going to 1.9" might create less turbulence and be quieter. I didn't think to test this because sometimes my brain doesn't work well, but give it a shot if you wanna experiment!

Motor mapping

I typically just wire things up in the most convenient/neat way possible, and then remap motors in software. I have no idea how the ESC<->FC signal wiring is mapped, plus I kept the motor wires long by wiring to ESCs that were further away, in order to maintain some slack (not to mention these Racerstar motor wires are really annoying to strip and tin).


Part List


RotorX Atom Mini 83 (16 builds)

Flight Controller

AirBlade Tiny Omnibus SBUS/PPM 16x16 F3 OSD Flight Controller with 4in1 5A 2S ESC (7 builds)
See Site


Cicada 4-in-1 5A 1S-2S 16x16 BLHeli_S DShot ESC (7 builds)


4 x AirBlade AB 1103 8000kV 2S-3S Brushless Racing Motors (flexible wires) (6 builds)


4X Racerstar Racing Edition 1103 BR1103B 10000KV 1-3S Brushless Motor Purple For 50 80 100 RC Drone FPV Racing RC Parts from  (9 builds)
See Site


DAL Cyclone 2035 Quad-Blade 2" Prop 8 Pack - Choose Your Color (9 builds)


Gemfan 2035BN Quad-Blade 2" Prop 4 Pack - Choose Your ColorPurple (15 builds)

FPV Camera

Crazepony FPV Micro AIO Camera 5.8G 40CH 25mW Video Transmitter VTX Switchable Raceband Support OSD FOV 150°for FPV Drone li (4 builds)


FrSky R-XSR 2.4GHz Micro ReceiverDefault Title (936 builds)


AirBlade Basic 300mAh 2S 7.4V 45C XT30 by Tattu (2 builds)


Turnigy nano-tech 300mah 2S 45~90C Lipo Pack (8 builds)


Glacier 25C 450mAh 2S 7.4V LiPo Battery with JST Connector (6 builds)


AirBlade Premium 500mAh 2S 7.4V 75C XT30 by Bonka (2 builds)

Misc Parts

Airblade/RotorX Atom Mini 83 canopy - the WRCKITX by deks_
See Site
Show stores (7)


Sign in to comment

ArcherFPV   Aug 26, 2018  

awesome build!!! i love the little guys

EnemyAce   Jul 20, 2018  

Helluva write-up, deks! Awesome build, too.

Rc Exp   Jul 20, 2018  

Really entertaing post! Thx for sharing and happy flights

Rc Exp   Jul 20, 2018 

Really like the canopy design btw

deks   Jul 20, 2018 


Fufalump   Jul 16, 2018  

Dude, this was well and far above the call of duty. I appreciate you and the time you spent on this more than you can imagine. I will treasure this build sir. Thank you <3

deks   Jul 16, 2018 


Guides & Reviews

Jun 21, 2021

AirbladeUAV has done it again and this time they've brought long range to the 5" class! Based on the popular Transformer Mini, the new Transformer 5" Ultralight adopts a lot of the same design philosophies with larger props and more payload capacity. It can fly upwards of 20 minutes on a 4 cell Li-Ion battery pack and in ideal conditions it's got a range of over 4 to 5 miles. In this guide I'll walk..

Read more
Mar 04, 2021

With the release of the DJI FPV Drone cinematic FPV has become a lot more accessible, but you certainly don't want to crash a $750 drone! The QAV-CINE Freybott is a compact, lightweight cinematic FPV drone that can take a hit and keep going. It's a lot safer to fly indoors and around people. With a naked GoPro or the SMO 4k you can capture some great stabilized footage. In this guide I'll show you..

Read more